1-800-242-2891

    

           OPEN MONDAY THRU FRIDAY 7:30 A.M. TILL 4:00 P.M. CENTRAL TIME       

DURABLE POLY FENDERS TAKE A BEATING - CLICK HERE

FENDERS HOGEBUILT CLICK HERE

The 379 Glider fits 379Peterbilts. Delivered in black gelcoat, these fenders can be mounted as-is or primed and painted.

The 379 Long fits 379 Peterbilts. Delivered in black gelcoat, these fenders can be mounted as-is or primed and painted.

BLOWOUT SPECIAL PRICING 

FIBERGLASS FENDERS WITH FLAME DESIGN

Click here to buy fenders online

800-242-2891

W.T.I. Full Fenders with Light Kits

      Full Fenders with Light Kits

Low Light Fenders with 3 angled oval lights	High Light Fenders on a Stainless Steel Panel

Low Light & High Light Fenders These two styles of fenders have the same unique features as our full fenders but with light boxes molded directly into the fender. The High Light Fenders have enough room for 3 round or rectangle lights. The Low Light Fenders have room for 3 round, rectangle, or oval lights set at an angle.

These lighted fenders have the light box enclosed in the rear so your tires are not throwing debris at your lights or wires. We offer a WTI wiring harness to fit these fenders. It comes in three sections, 2 fender harnesses and 1 "Y" truck harness. This will plug directly into your existing harness, then "Y" off to each fender and a center light panel if need be. Where each harness fonnects to the fender is a twist coupler, this lets you disconnect the wires to remove the fenders without cutting any wires. (Not available for Canadian axle spacing.) Lights are not included in the price, however, we have LED lights available upon request.

Gel Coat Colors

	Gray Primer
	Black
	White

Mounting Brackets

	Tubular steel with 1/4" wall
	Flat plates 3/8" thick
	Gusseted corners
	Mitered cuts
	Capped ends
	Grade 8 & stainless bolts included
	Built Tuff - Built to Last
	Available with Standard (52") axle spacing.
	Weight: 275 pounds per set (including brackets) (Approximate)

Complete step by step instructions (with pictures) are included with each kit.  Please note that due to the variations in each truck, final installation requires drilling into the frame and welding.

No mud flaps are not required on W.T.I. Fenders, however if you would prefer to have mud flaps we have a mud flap bracket available.  They are welded on to the bottom of the rear fender bracket.

Prices

Please note...... the wiring harness and lights are NOT included in the price of the light panel fenders.

Recommended 5th Wheel Height for all W.T.I. Fenders
(measure from ground to top of fifth wheel)

Click here to buy fenders online

1-800-242-2891

Full Fenders

W.T.I. 's full fiberglass fenders are just what you need to add the finishing touch to your truck or trailer.  Our fenders are hand fabricated using the highest quality fiberglass materials for long lasting durability.
The Full Fiberglass Fenders is the first product W.T.I. introduced. The fender you see today is actually the second generation of fender. The second generation fender was designed from the ground up, not a copy of some other fender.

When designing and engineering this fender many things were taken into consideration.

• First and foremost, looks. We wanted a fender that looked good yet is functional.
• A fender and bracket design that would fit most makes and models of trucks on the road today.
• Also, a fender that is durable and if damaged, easily fixable.

The WTI Full Fenders drop down and roll around farther on the tire than most fenders on the market today. This helps to keep road spray and debris from flying off your tires and hitting your truck or other traffic on the road.

We use a special liner for added strength and to improve wear against typical road hazards.  The underside flat area is reinforced with a special "V" laminated strip, which adds strength also.  This exclusive design requires no center mounting bracket or bracing.  This feature allows the fenders to move and flex with the frame. W.T.I. fenders are designed to be mounted on the front and rear, lower corners.

Gel Coat Colors

	Gray Primer
	Black
	White

Mounting Brackets

	Tubular steel with 1/4" wall
	Flat plates 3/8" thick
	Gusseted corners
	Mitered cuts
	Capped ends
	Grade 8 & stainless bolts included
	Built Tuff - Built to Last
	Available for either Standard (52") or Canadian (60") axle spacing.
	Weight: 275 pounds per set (including brackets) (Approximate)

Complete step by step instructions (with pictures) are included with each kit.  Please note that due to the variations in each truck, final installation requires drilling into the frame and welding.

No mud flaps are required on W.T.I. Fenders, however if you would prefer to have mud flaps we have a mud flap bracket available.  They are welded on to the bottom of the rear fender bracket.

Double Hump Fenders

Double Hump Fenders

The WTI Double Hump Fenders have the same styling as our single fenders with a few added features.

This fender is molded together in the middle. It gives you the look of two fenders, but it is actually one fender. The fender was lengthened on both ends and the middle, which allows easier access to the brackets on a truck with 24.5 tall tires. Also, on the lower outside center we have molded a place to add a side marker light.

There are three brackets used on each side of the truck to give proper support to the fender.  The same "hidden" bracket design is used on the "double humps" that is used on the regular full fenders with an added supporting bracket in the middle.   

Gel Coat Colors

	Gray Primer
	Black
	White

Mounting Brackets

	Tubular steel with 1/4" wall
	Flat plates 3/8" thick
	Gusseted corners
	Mitered cuts
	Capped ends
	Grade 8 & stainless bolts included
	Built Tuff - Built to Last
	Available with Standard (52") spacing
	Weight: 275 pounds per set (including brackets) (Approximate)

Recommended 5th Wheel Height for all W.T.I. Fenders
(measure from ground to top of fifth wheel)

If you have:
22.5 low pro tires	48"
22.5 standard tires	49"
24.5 low pro tires	49"
24.5 tall rubber	51"

This is the minimum height we recommend. This does not guarantee you will not hit the fenders with the trailer, but in our experience it has been sufficient. The higher the 5th wheel the better!

Click here to buy fenders online

1-800-242-2891

 

---

Single Fenders

W.T.I. Single Axle Fenders will look great on your spread axle trailer and other axle configurations.  These fenders are hand fabricated with high quality fiberglass materiel for long lasting durability. Bracket Sets are now available for the Utility and Great Dane sprad axle trailers.

The side of this fender can be ordered so you show a lot of your tire or ordered so it covers half of your tire up. When the single fenders are mounted on a tandem axle truck they do require a center mounting bracket.

W. T. I. Single Axle Fenders on a Spread Axle Trailer

Gel Coat Colors

• Gray Primer
• Black
• White

W. T. I. Single Axle Fenders on a Tractor

W.T.I. Single Axle Fenders without brackets
Paint

Single Axle Fenders with brackets on trailers
Single Axle Fenders with brackets on tractors
Paint

Click here to buy fenders online

Recommended 5th Wheel Height for all W.T.I. Fenders
(measure from ground to top of fifth wheel)

If you have:
22.5 low pro tires	48"
22.5 standard tires	49"
24.5 low pro tires	49"
24.5 tall rubber	51"

This is the minimum height we recommend. This does not guarantee you will not hit the fenders with the trailer, but in our experience it has been sufficient. The higher the 5th wheel the better!

W.T.I. Peterbilt Classic Front Fenders 

Add a distinctive, nostalgic look to your 379 Peterbilt with W.T.I.'s Classic Front Fenders.  The fenders have been created to close in the wheel opening and the flowing rear tail gives your 379 Peterbilt the "50's" look. The hand fabricated fiberglass fenders are exclusively designed to fit the 379 Peterbilt with the extended hood. In addition to the good looks, we use double wall construction so the finish is fully protected from road hazards.  No special mounting brackets are required and can be installed in minutes.

Features

• Double wall contruction, no fender liners are needed.
• Classic wing in rear with mud flap bracket attached. All you need is to add your flap.  
• A "handle" was created for easy lifting of your hood.  
• Turn signals can be mounted on the top or lower side of the fender.

Peterbilt Front Fenders (set)
Paint - varies by color

 

Recommended 5th Wheel Height for all W.T.I. Fenders
(measure from ground to top of fifth wheel)

If you have:
22.5 low pro tires	48"
22.5 standard tires	49"
24.5 low pro tires	49"
24.5 tall rubber	51"